Looking for:
2007 audi a4 owners manual download |
Audi A4 B7 Owner's Manual – PDF Download
Wait until you can no longer see or hear escaping steam or coolant. Caution Additional lights and other accessories in front of the air inlet reduce the cooling effect of the radiator. At high outside tempera-tures and high engine loads, there is a risk of the engine over-heating.
The front spoiler also ensures proper distribution of the cooling air when the vehicle is moving. If the spoiler is damaged this can reduce the cooling effect, which could cause the engine to overheat.
You should obtain professional assistance. Rev counterThe rev counter indicates the number of engine revolu-tions per minute.
You should select a lower gear if the engine speed drops below rpm. The start of the red zone on the dial indicates the maximum engine speed which may be used briefly when the engine is warm and after it has been run in properly. However, it is advisable to change up a gear or move the selector lever to D or lift your foot off the accelerator before the needle reaches the red zone.
CautionNever allow the rev counter needle page 11, fig. The start of the red zone on the dial is different for some engine versions.
For the sake of the environmentChanging up a gear early will help you to save fuel and minimise engine noise. Starting check procedure auto-check control The auto-check control checks important components and vehicle systems. These background checks are run constantly, as long as the ignition is switched on page You can start the check procedure manually by pressing the button with the ignition switched on. Calling up driver messages againA red or yellow symbol appearing in the instrument cluster display is normally accompanied by a corresponding message.
The message will disappear from the display after about 5 seconds. If required, you can call up the message again by briefly pressing the button. Setting speed warningYou can press the button briefly to set speed limit warning 1 while the vehicle is moving page If you press and hold the button, this will cancel the speed warning.
It is then not possible to change the minutes or the date manually. Note The digital clock and mileage recorder displays are switched on for about 30 seconds when the driver's door is opened.
When the ignition is switched off, the clock and date display can be switched on for about 30 seconds by pressing the button page 12, fig. The mileage is stated in kilometres km or miles. The trip recorder shows the distance that has been travelled since it was last reset.
It is used to measure individual journeys. The last digit of the trip recorder indicates distances of metres or tenths of a mile. The trip recorder can be reset to zero by pressing the reset button fig. Fault displayIf there is a fault in the instruments, the letters dEF appear perma-nently in the trip recorder display. Please have the fault rectified as soon as possible. ImmobiliserWhen the ignition is switched on, the security programming of the ignition key is verified electronically.
If an uncoded key is used, SAFE will appear continuously in the mileage recorder display. The vehicle cannot then be driven page Note The date, time and recorded mileage will continue to be displayed for about 30 seconds after you switch off the ignition. The digital clock and mileage recorder displays are switched on for about 30 seconds when the driver's door is opened.
When the ignition is switched off, the mileage recorder can be switched on for about 30 seconds by pressing the button page 12, fig. Fuel gaugeThe gauge only works when the ignition is switched on.
When the needle reaches the reserve zone, the symbol page 37 lights up in the instrument cluster display together with the message Please refuel. At this point there are still about 8 litres of fuel left in the tank. This is your reminder to fill up soon. The tank capacity of your vehicle is given in the Technical data section. The irregular supply of fuel can cause misfiring, which would allow unburnt fuel to enter the exhaust system.
This can lead to overheating and damage to the catalytic converter. Warning and indicator lampsOverviewThe warning and indicator lamps indicate a number of different functions and possible faults. Juli 09Driver information system 30 Speed warning - to set the speed above which a warning signal will sound. Auto-check controlIntroductionThe auto-check control checks important components and vehicle systems.
These background checks are run constantly, as long as the ignition is switched on. A message is displayed in the instrument cluster if a fault should occur or if any maintenance or repairs are urgently required. This is accompanied by an audible warning signal. Depending on the priority of the fault, a red or yellow warning symbol lights up in the display.
The red symbols indicate a serious malfunction, whereas the yellow ones represent other malfunctions or items requiring attention. Additional messages to assist the driver may be shown with the red or yellow symbols. If the selector lever is in position P or N, the following instruction will appear:When stationary apply footbrake while selecting gearWhen a gear R, D etc.
The driver message will disappear 30 seconds after switching on the ignition or earlier, if there are other driver messages or malfunc-tions. If one or more faults are detected, the driver information message as above will disappear about 15 seconds after the engine has been started and the appropriate fault symbol s will appear in the display. The warning display will be accompanied by the corre-sponding warning chime.
Applies to vehicles: with speed warning functionDriver messagesAdditional messages to assist the driver are displayed together with the warning symbols in the instrument cluster. Doors do not lock if lever is not in P. The ignition key can only be withdrawn when the selector lever is in this position. Similar messages will be displayed if other functions of this kind cannot be carried out. Driver messages and red symbolsIf a red warning symbol appears in the display, it will automatically be accompanied by the corresponding driver message.
Juli 09Driver information system 31Controls Safety Driving tips General maintenance Self-help Technical dataFor example, in the event of an oil pressure malfunction the oil pres-sure symbol will appear in the display. In addition, the following message will appear:Switch off engine and check oil levelThe message will disappear from the display after about 5 seconds. If required, the message can be called up again by briefly pressing the button page 30, fig. Driver messages and yellow symbolsIf a yellow warning symbol appears in the display, it will automati-cally be accompanied by the corresponding driver message.
For example, if the symbol appears windscreen washer fluid low , the display will also show the message:Please top up washer fluidThe message will disappear after a few seconds. If required, the message can be called up again by briefly pressing the button.
Red symbolsA red symbol warns of a serious malfunction. Stop the vehicle. Switch off the engine. Check the function displayed. Obtain professional assist-ance if necessary. The red symbols indicate a Priority 1 fault serious malfunction.
Should a Priority 1 fault occur, a red warning symbol will appear at the top of the display fig. The symbol is accompanied by a driver message giving you more information about the fault. This symbol is accompanied by three warning chimes. The symbol will keep flashing until the fault is corrected. If several Priority 1 faults are detected at the same time, the symbols are displayed one after the other for about 2 seconds at a time. This message will disappear after about 5 seconds, but you can call it up again at any time by pressing the button page Juli 09Driver information system 32Alternator fault If the symbol flashes in the instrument cluster display, there is an alternator fault or a fault in the vehicle's electrical system.
In addi-tion, a message will appear. This message will disappear after about 5 seconds, but you can call it up again at any time by pressing the button. You should normally be able to drive to the next available qualified workshop. However, you should avoid using electrical equipment that is not absolutely necessary because this will drain the battery. CautionIf the coolant warning lamp in the instrument display lights up as well as the alternator warning lamp while driving page 33, stop the vehicle immediately and switch off the engine.
In this case the coolant pump is no longer being driven, and there is a risk of engine damage. Fault in the brake system CA fault in the brake system should be corrected as soon as possible. If the symbol C flashes in the display, there is a fault in the brake system. This message will disappear after about 5 seconds, but you can call it up again at any time by pressing the button:Stop vehicle and check brake fluid level Stop the vehicle.
Check the brake fluid level page Obtain professional assistance if necessary. Fault in ABS brake system. Contact workshop Drive carefully to the nearest qualified workshop and have the fault rectified.
Parking brake! Please contact workshop If the symbol appears after you switch on the ignition when the vehicle is stationary, please check whether you can release the parking brake. If this is possible, you should drive without delay to the nearest qualified work-shop and have the fault rectified. If the parking brake cannot be released you should obtain professional assistance. If this symbol should appear while driving, there may be a malfunction in the drive-away assist or the emergency brake functions.
You may not be able to apply the parking brake. It is also possible that you cannot release the parking brake after it has been applied. Drive the vehicle to a qualified workshop and have the fault repaired. WARNING Before opening the bonnet and checking the brake fluid level, observe the warning information on page , Working on components in the engine compartment.
If the brake fluid level in the reservoir is too low, this could result in an accident. Do not drive on. You should obtain profes-sional assistance. If the brake warning lamp lights up together with the ABS warning lamp, this can mean that the control function of the ABS is out of action. Juli 09Driver information system 33Controls Safety Driving tips General maintenance Self-help Technical dataeasily when braking.
This could cause the tail of the vehicle to skid sideways. Drive carefully to the nearest qualified workshop and have the fault rectified. NoteThe warning lamp C in the instrument cluster will start flashing as well if there is a fault in the brake system.
Fault in the cooling system Faults in the cooling system must be rectified immedi-ately. If the symbol flashes in the display, this means that either the coolant temperature is too high or the coolant level is too low. This message will disappear after about 5 seconds, but you can call it up again at any time by pressing the button:Switch off engine, check coolant level Stop the vehicle. Check the coolant level page Add more coolant if necessary page Wait for the symbol to go out before driving on.
If the coolant level is correct, the overheating may be caused by a malfunction of the radiator fan. If the alternator warning lamp lights up as well page 32, it is possible that the drive belt has broken. Juli 09Doors and windows 42Doors and windowsCentral locking systemDescriptionThe vehicle can be locked and unlocked via the central locking system. The vehicle is unlocked again when the ignition key is removed.
Alternatively, the vehicle can also be unlocked via the central locking switch or by pulling one of the inside door handles. In the event of an accident in which the airbags inflate, the doors will be automatically unlocked to facilitate access and assistance.
Deadlock mechanismThe central locking system is combined with a deadlock mecha-nism. Once the vehicle has been locked from the outside, the door handles on the inside are deactivated. This makes it more difficult to break into the vehicle. The anti-theft alarm system switches on automatically when the vehicle is locked. It switches off automatically if you unlock the vehicle using the remote control.
If you unlock the vehicle by inserting the key in the driver's door, the ignition must be switched on within 15 seconds, otherwise the alarm will be triggered. On some export versions, the alarm is trig-gered immediately when you open a door.
To deactivate the alarm, press the unlock button on the remote control key or switch on the ignition. The alarm will also switch itself off when it comes to the end of its cycle. Switch off the interior monitor and tow-away protection if you wish to prevent the alarm from being triggered accidentally page Turn signalsThe turn signals will flash twice when the vehicle is unlocked and once when the vehicle is locked.
If the turn signals do not flash, one of the doors, the bonnet or the boot lid is still open. Accidental lock-outThe central locking system prevents you from being locked out of the vehicle in the following situations: When the driver's door is open, it cannot be locked together with the other doors by pressing the central locking switch and then closing the door page Juli 09Doors and windows 43Controls Safety Driving tips General maintenance Self-help Technical dataTo prevent yourself from being locked out, do not lock the vehicle with the remote control key before closing the doors or boot lid.
If you accidentally press the locking button on your remote control key when any of the doors except for the driver's door are open, then put the key down inside the car and forget to take it with you when you close the doors, you can still open the doors for about one minute before the vehicle is locked.
WARNINGDo not leave anyone especially children in the car if it is locked from the outside and the deadlock mechanism is activated: the doors and windows cannot then be opened from the inside.
Locked doors could delay assistance in an emergency, potentially putting lives at risk. Note Never leave any valuable items in the vehicle unattended. Even a locked vehicle is not a safe. Please have the malfunc-tion repaired by an Audi dealer or qualified workshop. Set of keys Remote control keyThe remote control key will lock and unlock the car and start the engine.
Spare keyThe spare key is intended for temporary use only and should be used only in an emergency. Keep it in a safe place and do not carry it on the keyring. Replacing a keyIf you should lose a key, please contact an Audi dealer.
Have the remote control coding for that key deactivated. For this purpose you should bring all available keys with you. It is also important to notify your insurance company if a key has been lost. Electronic immobiliserThe immobiliser is designed to prevent unauthorised persons from driving the vehicle. If an uncoded key is used, SAFE will appear in the mileage recorder display.
It may not be possible to start the engine with the key if there is another ignition key from a different make of vehicle on the same key ring. Juli 09Doors and windows 44Data stored on remote control keyData related to the service and maintenance of the vehicle are stored continuously on your remote control key.
Your Audi dealer can read out the data and will then be able to tell you what service work is required.
This also applies to vehicles with advanced key. Personal convenience settingsIf two people use the same car regularly, it is a good idea for each person to have his or her own remote control key. This is especially important if children are left in the car. They might otherwise be able to start the engine or use power-operated equipment such as the electric windows - this could lead to injuries.
Wait for the vehicle to come to a standstill before removing the ignition key from the lock. Otherwise the steering lock could engage suddenly, causing an accident. NoteThe function of the remote control key may be impaired by interfer-ence from other nearby radio signals for example from a mobile telephone or TV transmitter if these are in the same frequency range.
Indicator lamp on remote control keyThe indicator lamp on the remote control key lights up when you press the buttons. The indicator lamp should light up once briefly when you press one of the buttons briefly.
If the indicator lamp does not light up, this means the battery is exhausted and must be replaced page The instrument cluster display also shows the symbol and the following message if the battery is exhausted:Please change key batteryFig. Juli 09Doors and windows 45Controls Safety Driving tips General maintenance Self-help Technical dataReplacing the battery for the remote control key Press the release button fig.
Pull the emergency key out of the remote control key. Press the release catch fig. Slide the battery carrier carefully into the remote control key. The sun visors can improve visibility and contribute to safety. To increase the sensitivity level of the — Juli 09 Lights and vision Service position Note Use the service position to change the wiper blades. Check that the washer fluid reservoir is full before starting a long journey. Worn or dirty wiper blades can cause smearing on the glass which can also impair the effectiveness of the rain sensor.
Juli 09 Lights and vision when they are in the service position you will also avoid damaging — Lift the wiper arm away from the glass. Juli 09 Lights and vision Anti-dazzle setting when the interior lighting is switched on when reverse gear is engaged — Pull the lever at the bottom of the mirror towards you. WARNING Applies to vehicles: with automatic anti-dazzle adjustment for interior mirror Automatic anti-dazzle adjustment Electrolyte fluid can leak from a broken mirror.
Juli 09 Lights and vision Digital compass Applies to vehicles: with automatic anti-dazzle adjustment for exterior mirrors Automatic anti-dazzle adjustment for exterior mirrors Applies to vehicles: with digital compass Activating and deactivating the compass The exterior mirrors darken together with the automatically The compass direction will appear in the mirror. Juli 09 Lights and vision Applies to vehicles: with digital compass Applies to vehicles: with digital compass Setting the correct compass calibration zone Calibrating compass The correct compass calibration zone must first be set The compass must be re-calibrated if the display is incor- before the compass can give an accurate reading.
Juli 09 Seats and storage Seats and storage Manual adjustment of front seats Applies to vehicles: with manual seat adjustment Seat adjustment Applies to vehicles: with manual seat adjustment It is possible to adjust the position and shape of the seat Seat adjuster controls manually so that you can travel in a safe and comfortable sitting position.
Juli 09 Seats and storage Adjusting contour of lumbar support WARNING — Press the front or rear of switch to increase or Never adjust the driver's seat when the vehicle is moving - this decrease the curvature of the lumbar support as could lead to an accident. Juli 09 Seats and storage belts, the head restraints offer effective protection, provided they Applies to vehicles: with front armrest are properly adjusted.
Front armrest The armrest can be adjusted to several positions and Adjusting the rear head restraints moved back and forwards. This is especially important for heavy Loads in the luggage compartment should be safely objects.
Juli 09 Seats and storage Fig. Juli 09 Seats and storage Applies to vehicles: with load-through hatch Caution Load-through hatch with transport bag When returning the backrest to an upright position, make sure that You can use the load-through hatch and the removable the seat belts for the outer rear seats are in their guides so that they ski bag to transport skis or other extra-long objects safely cannot be caught up and damaged in the catches for the backrest.
Page Roof Carrier Special fixtures must then be added in order to safely transport luggage, bicycles, skis, surf boards or boats on the Storage roof. All the elements of this system are available from Audi dealers. Juli 09 Seats and storage Attachment points Roof load The roof carrier must be attached at the marked points Loads carried on the roof must be securely attached.
The only. The maximum permissible roof load for your vehicle is 90 kg. Juli 09 Seats and storage Cup holders — Position the cup in the holder and let go of the arm. The arm will move back automatically to secure the cup. Closing cup holder — Juli 09 Seats and storage Cigarette lighter and electrical The cigarette lighter employs a standard 12 Volt socket which can also be used as a power source for electrical appliances.
The appli- sockets ances connected to the socket must not exceed a power rating of W. Juli 09 Seats and storage — Insert the plug of the electrical appliance into the socket. Applies to vehicles: with 12 Volt sockets 12 Volt sockets Electrical equipment can be connected to the 12 Volt socket.
The Electrical equipment can be connected to both 12 Volt appliances connected to the socket must not exceed a power rating sockets. Juli 09 Seats and storage If you connect more than one appliance, the total power rating of all Applies to vehicles: with Volt Euro socket On-board Volt Euro socket appliances must not exceed W.
If necessary, check the type plates on the connected appliances for details of the power ratings. Page Storage Compartments In this case, a different type of inverter must be installed in the vehicle. Retrofit kits are available from your Audi dealer. Do not connect Volt appliances to the Volt Euro socket. Interference can occur on the radio's AM waveband if electrical Fig.
Always keep the compartment cover closed while the vehicle is in motion to reduce the risk of injury during a sudden braking manoeuvre or in the event of an accident. Juli 09 Seats and storage Note The storage compartment will hold a maximum weight of 1 kg.
Juli 09 Heating and cooling Heating and cooling Deluxe automatic air conditioner The compressor also switches off if the coolant temperature is excessively high, to ensure adequate engine cooling under extreme loads. Applies to vehicles: with deluxe automatic air conditioner Description Pollution filter The pollution filter a particle filter serves as a barrier against impu Page 96 Repairs to the Audi air conditioner require specialist knowledge and special tools.
For this reason, please contact a qualified work- shop if the system is not working properly. Juli 09 Heating and cooling You can use the air distribution setting to select the air outlets you The rear window heating only works when the engine is running. Juli 09 Heating and cooling — The direction of air delivery from these outlets can be Note adjusted horizontally and vertically using the adjuster in If the LED in the AC button should continue to light up when the AC the centre of each outlet grille.
Juli 09 Heating and cooling adequate cooling effect, you should not close these outlets Deluxe automatic air conditioner - completely. Juli 09 Heating and cooling If the humidity and temperature outside the vehicle are high, Applies to vehicles: with diesel engine Supplementary heater condensation can drip off the evaporator in the air cooling system and form a pool underneath the vehicle. Juli 09 Heating and cooling instance, that the rear window heater is not working, it may have Applies to vehicles: with deluxe automatic air conditioner plus been temporarily switched off by the power management function, Controls or regulated to a lower heat output.
Juli 09 Heating and cooling interior temperature as quickly as possible, and then to maintain this temperature. The system automatically compensates for any variations in the outside temperature and for the effect of direct sunlight.
Juli 09 Heating and cooling Switch to for automatic control of the air distribution. Juli 09 Heating and cooling remain on until the ignition is switched off. When the rear window Applies to vehicles: with deluxe automatic air conditioner plus heating is switched on, this setting will remain activated for 15 Air outlets minutes after switching off the ignition. Juli 09 Heating and cooling Applies to vehicles: with deluxe automatic air conditioner plus Note Economical operation of the air conditioner When the air conditioner is operating in the cooling mode, the air is Economical operation of the air conditioner will help to directed mainly to outlets.
Juli 09 Heating and cooling Deluxe automatic air conditioner plus Applies to vehicles: with deluxe automatic air conditioner plus Automatic recirculation - basic settings If the outside air is polluted, an air purity sensor in the vehicle will automatically switch on the air recirculation.
This feature can be used to cool the interior with the blower when the vehicle is left parked in the sun. Pressing the button a second time will switch on the It is advisable to open the air outlets when using the auxiliary blower again. Juli 09 Heating and cooling Transmitting range The range of the remote control transmitter is about metres.
However, this can be greatly reduced by obstacles buildings, etc. Hold the aerial upright when using the remote control. Juli 09 Heating and cooling Applies to vehicles: with seat heating for rear seats Seat heating for rear seats The seat cushions and backrests of the two outer rear seats can be heated electrically.
Juli 09 Driving Driving Steering Ignition lock Applies to vehicles: with manually adjustable steering column Starting the engine with the key Adjusting the steering wheel position You can use the ignition key to switch on the ignition and The height and reach of the steering wheel can be start the engine. Juli 09 Driving If you press in the key without pressing the clutch or brake pedal, position P you will not be able to lock the vehicle using the exterior the ignition will be switched on or off.
The steering lock is released locking switch on the door handle or the remote control key. This would mean a greater risk of accidents and serious injury, because you Fig. The steering lock acts as a theft deterrent. Juli 09 Driving start running again after some time if the coolant temperature rises When driving away due to a build-up of heat, or if the engine is hot and the engine The parking brake auto release function releases the parking compartment is heated up further by direct sunlight.
Juli 09 Driving a fault in the parking brake. Page Audi Hold Assist Driving Press brake pedal to release parking brake When the Audi hold assist function is on, the vehicle is auto- matically prevented from rolling away and you no longer This message may appear when you press the switch to release the parking brake.
Page Cruise Control System Once it detects that the Audi hold assist can be switched on only when the driver's door vehicle is stopped, Audi hold assist keeps the vehicle stationary. The is closed, the driver's seat belt is buckled and the engine is running. Juli 09 Driving WARNING continued When you take a turn-off, drive along a motorway exit lane or pass through roadwork sections, please temporarily switch off the cruise control system.
Please make sure you do not unintentionally rest your foot on the accelerator - this will override the cruise control system which, as a result, will not brake the vehicle. Juli 09 Driving be deactivated temporarily. Juli 09 adaptive cruise control ACC Applies to vehicles: with adaptive cruise control and manual gearbox WARNING continued Vehicles with manual gearbox Adaptive cruise control will not react when approaching a The driver of a vehicle with a manual gearbox of course stationary obstacle, e.
Juli 09 adaptive cruise control ACC If the vehicle in front accelerates, the adaptive cruise control will Applies to vehicles: with adaptive cruise control How does the distance control work? Vehicles in front are detected by a radar sensor. Juli 09 adaptive cruise control ACC — Drive at the desired speed. The target speed you When setting the distance, the driver is responsible for adhering have set is marked by diodes in the speedometer.
Juli 09 adaptive cruise control ACC Target speed Applies to vehicles: with adaptive cruise control Instrument cluster display The target speed set by the driver is indicated by a red diode in the speedometer. Juli 09 adaptive cruise control ACC Vehicle in front: If a vehicle is detected in front, the arrows will be Applies to vehicles: with adaptive cruise control on the scale. The green area of the scale represents the distance System status indicator in the instrument setting.
If the sensor is no longer functioning due to Driver intervention prompt dirt or obstruction in this area, it should be cleaned. Setting the warning tone volume and driving program Note You can change the adaptive cruise control settings on Page Audi Braking Guard Fig. Page If the vehicle in front of you is travelling in the same lane at a much being reliably recognised or, in some circumstances, not being slower speed or if it brakes hard, the Audi braking guard will calcu- detected at all.
Always keep the road ahead within your field of late the time at which a collision can be avoided only by emergency vision. System - The Audi braking guard system can be switched on and off. Early warning - The acoustic signals and display messages can be switched on and off. Note The settings are stored on the remote control key in use. This can result in the system not detecting the lane Applies to vehicles: with lane assist markings correctly. Page Seite Donnerstag, Juli 09 Audi lane assist driving on a straight section.
On narrow roads, the system will give off warnings later than on wide roads. The warning lamp on the left-hand mirror assists the The red indicator To avoid impairing the function of the side assist, do not attach lamp in the button will light up. Juli 09 Audi side assist on the relevant exterior mirror will light up whenever the side assist Applies to vehicles: with side assist Area covered by the radar sensors calculates that the distance and the speed differential of approaching vehicles would be critical in the event of a lane change.
Juli 09 Audi side assist Warning mode Warning lamp on exterior mirror does not light up If you operate the turn signal when the side assist has detected a The sensors have not detected any vehicles. Juli 09 Audi side assist attention to the presence of a vehicle which you may have Applies to vehicles: with side assist Situation when you are slowly overtaking overlooked.
The side assist system has inherent limitations in some situations. The brightness of the warning lamp in both the information and Page Notes Fig. To ensure the proper function of the side assist system, do not attach any objects such as stickers or bicycle carriers, etc. The front grille assembly changed to a tall trapezoidal shape in the same manner as the C6 third-generation Audi A6. Audi's internal platform nomenclature uses PL46 p assenger car l ongitudinal platform, size 4 , generation 6 for both B6 and B7 chassis.
Performance kW PS at rpm. Acceleration 8. Fuel diesel. Engine 1 ccm cui , 4-cylinder, In-Line, valves. Fuel gasoline. Engine 1 ccm cui , 4-cylinder, In-Line. Performance kW PS. Thread: Anyone have a A4 owners manual pdf. Thread Tools Show Printable Version.
My Photo Gallery: 0. My Classifieds: 0. Anyone have a A4 owners manual pdf Guest-only advertisement. Register or Log In now! Hello All, Any one have a pdf of a A4 owners manual. Thanks in advance. I didn't get one with mine. Just throwing this out there for any who don't know: There is a small compartment beneath the steering wheel where the manual goes.
Check there and see if your manual has been hiding there all along. Don't be too embarrassed, it happens to all first time Audi owners
❿2007 audi a4 owners manual download
A4 changing cam follower. A4 arm rest fix. A4 changing front springs. A4 fixing sunroof rattle. A4 fixing front wiper blades. A4 changing fuel filter. Control for Audi drive select Instrument cluster overview Note The instrument cluster is the driver's information centre. The instrument shows how far you have travelled. Fault display If there is a fault in the instruments, the letters dEF appear perma- nently in the trip recorder display.
If the warning lamp Note goes out, this means the system is fully functional. This warning lamp monitors the Audi hold assist function. Page 22 Seite 20 Donnerstag, This is to warn the driver to take extra care when there is a risk of ice on the road. When the vehicle is stationary or travelling at very low speeds, the temperature displayed may be slightly higher than the actual outside temperature as a result of the heat radiated from the Juli 09 Driver information system certain situations, only the driver can choose the correct gear for instance when overtaking, driving up a steep gradient or towing a trailer.
Page On-Board Computer The display may not be complete on new vehicles within the first km. On-board computer Resetting the service interval display Your Audi dealer resets the display after each service.
You can only Applies to vehicles: with on-board computer reset the oil change display yourself. Driving time This display shows the period of time which has elapsed since the memory was last cancelled.
Juli 09 Driver information system Driving time and can be switched back on at any time so that they again appear in the display. Juli 09 Driver information system need to keep below a particular speed when winter tyres are fitted, Clearing speed limit etc. Juli 09 Driver information system Speed warning - to set the speed above which a warning signal If one or more faults are detected, the driver information message will sound.
Juli 09 Driver information system For example, in the event of an oil pressure malfunction the oil pres- — Switch off the engine. In addition, the following — Fault in ABS brake system. This could cause the tail of the vehicle to skid sideways. Juli 09 Driver information system 5 seconds, but you can call it up again at any time by Yellow symbols indicate a Priority 2 fault.
The symbol is accompanied by a driver message giving you more infor- Ignition lock defective. The glass can break when you touch the bulb, causing injury. Page Tyre Pressure Monitoring System Take the vehicle to a qualified workshop to have the problem remedied. Unauthorised use of these Juli 09 Doors and windows Doors and windows Central locking system handles on the inside are deactivated.
This makes it more difficult to break into the vehicle. Page 45 Please have the malfunc- tion repaired by an Audi dealer or qualified workshop. If you should lose a key, please contact an Audi dealer. Have the remote control coding for that key deactivated. Page 46 Data related to the service and maintenance of the vehicle are The function of the remote control key may be impaired by interfer- stored continuously on your remote control key.
Your Audi dealer ence from other nearby radio signals for example from a mobile Juli 09 Doors and windows Replacing the battery for the remote control — Insert the emergency key.
For the sake of the environment Used batteries must be disposed of appropriately and must not be discarded with ordinary household waste. Make sure that the Audi rings are facing upwards. Page 49 60 seconds after unlocking the car. This function prevents the vehicle from remaining Fig. Juli 09 Doors and windows Locking the vehicle Note — Move the selector lever to position P automatic Please note the following points if the vehicle is left parked for long gearbox , otherwise it will not be possible to lock the periods: vehicle.
Juli 09 Doors and windows Locking Central locking switch — Move the selector lever to position P automatic gearbox. Juli 09 Doors and windows You can still unlock all doors and the luggage compartment.
Locked doors could delay assistance in an emergency, poten- When you lock the vehicle, the central locking system will automat- tially putting lives at risk. The diode in the — The boot lid will lock automatically when you close it again. Manual release of the boot lid Fig. Juli 09 Doors and windows Child-proof catches Electric windows Child-proof catches on the rear doors Controls The child-proof catches prevent the rear doors being The driver can operate all the electric windows.
Juli 09 Doors and windows — You can set the roof to an intermediate position by Closing the sun roof manually turning the switch to the desired position.
The sun roof can be operated for about ten minutes after the igni- tion has been switched off. Page 61 Vehicles with halogen headlights: Opaque stickers should be applied to certain parts of the headlight lenses. For further informa- Important:. Instrument lighting When the dipped beam headlights are switched on, the — Headlights with xenon gas-discharge bulbs automatically adapt to suit the load being carried when the engine is switched on.
If your vehicle is being towed away, or if you are towing another — Juli 09 Lights and vision Clear vision Applies to vehicles: with sun blinds Sun blinds Sun visors Sun blinds are provided for the rear window and the rear side windows. The sun visors can improve visibility and contribute to safety. To increase the sensitivity level of the — Juli 09 Lights and vision Service position Note Use the service position to change the wiper blades.
Check that the washer fluid reservoir is full before starting a long journey. Worn or dirty wiper blades can cause smearing on the glass which can also impair the effectiveness of the rain sensor. Juli 09 Lights and vision when they are in the service position you will also avoid damaging — Lift the wiper arm away from the glass. Juli 09 Lights and vision Anti-dazzle setting when the interior lighting is switched on when reverse gear is engaged — Pull the lever at the bottom of the mirror towards you.
WARNING Applies to vehicles: with automatic anti-dazzle adjustment for interior mirror Automatic anti-dazzle adjustment Electrolyte fluid can leak from a broken mirror. Juli 09 Lights and vision Digital compass Applies to vehicles: with automatic anti-dazzle adjustment for exterior mirrors Automatic anti-dazzle adjustment for exterior mirrors Applies to vehicles: with digital compass Activating and deactivating the compass The exterior mirrors darken together with the automatically The compass direction will appear in the mirror.
Juli 09 Lights and vision Applies to vehicles: with digital compass Applies to vehicles: with digital compass Setting the correct compass calibration zone Calibrating compass The correct compass calibration zone must first be set The compass must be re-calibrated if the display is incor- before the compass can give an accurate reading.
Juli 09 Seats and storage Seats and storage Manual adjustment of front seats Applies to vehicles: with manual seat adjustment Seat adjustment Applies to vehicles: with manual seat adjustment It is possible to adjust the position and shape of the seat Seat adjuster controls manually so that you can travel in a safe and comfortable sitting position. Juli 09 Seats and storage Adjusting contour of lumbar support WARNING — Press the front or rear of switch to increase or Never adjust the driver's seat when the vehicle is moving - this decrease the curvature of the lumbar support as could lead to an accident.
Juli 09 Seats and storage belts, the head restraints offer effective protection, provided they Applies to vehicles: with front armrest are properly adjusted. Lol I noticed it the day I got my car, last week my friend calls me "Hey just found out a compartment under the seat! I have two of them i think they are both 07 If someone wants one i'll give it to you, you just pay shipping. I'll check friday when I get my car back. Can someone post a pic of where exactly this compartment is. I have an 07 Cabriolet and cannot find it to save my life.
The one under my seat it there but I feel like a fool reaching all under the steering wheel trying to find it. Originally Posted by BladesBravo. Originally Posted by freaksavior. View the manual for the Audi A4 here, for free. This manual comes under the category Cars and has been rated by 17 people with an average of a 8. This manual is available in the following languages: English.
Do you have a question about the Audi A4 or do you need help? Ask your question here. Do you have a question about the Audi and the answer is not in the manual? Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Audi owners to provide you with a good answer.
Audi Q2 Owner's Manual. Popular Models Mazda Mazda3. Number plate light. Technical data. Explanation of technical data. Vehicle identification data. Performance, weights and dimensions. Petrol engines. Diesel engines. Please ensure that this Owner's Manual is always kept in the vehicle. It should always be available to anyone else driving the vehicle, i. This manual describes the equipment available for the vehicle at the time of going to print. Some of the equipment described here will not be available until a later date, or may only be available in certain markets.
Some sections of this Owner's Manual do not apply to all vehicles. If this is the case, a text at the start of the section indicates which vehicles it applies to, e. Applies to vehicles: with auxiliary heater. Illustrations are intended as a general guide, and may vary from the equipment fitted in your vehicle in some details. At the beginning of this Owner's Manual, you will find a table of contents showing all the items described in this manual in the order in which they appear. An alphabetical index is included at the end of the Owner's Manual.
All references to positions such as left, right, front or rear are given as seen facing in the direction of travel. M Denotes the end of a section. Registered trademarks are marked. However, the absence of this symbol does not constitute a waiver of the rights concerning any proprietary name.
They warn you of serious dangers, possibly involving accident or injury. CautionTexts with this symbol draw your attention to a possible risk of damage to your vehicle. For the sake of the environmentTexts with this symbol refer to points relevant to the protection of the environment.
NoteTexts with this symbol contain additional information of a more general nature. Juli 09Controls and displays 8Fig. Electric adjuster for exterior mirrors. Central locking switch. Button for side assist. Light switch. Instrument lighting. Control lever for: Turn signals and main beam headlights. Headlight range control. Steering wheel with: Horn Driver's airbag.
SET button. Instrument cluster. Reset button for trip recorder. Control lever for: Windscreen wipers and washer. Air outlets with thumbwheel. For deluxe automatic air conditioner. For deluxe automatic air conditioner plus. Front passenger's airbag. Switches for the following as applicable : Audi parking system.
Electric sun blind. Control for Audi drive select. Air conditioner, depending on equipment fitted: Deluxe automatic air conditioner. Ashtray with cigarette lighter. Depending on gearbox fitted, gear lever or selector lever for: multitronic. As the two displays are more or lessidentical this Owner's Manual uses the multi-coloured displays for illustra-tion purposes. Juli 09Controls and displays 10 Switch for electric sun blind. Electro-mechanical parking brake.
Adjustable steering column hidden behind steering wheel. Depending on equipment fitted: Cruise control system. Switch for releasing the boot lid. However, the symbols used to identify the controls are the same. Rev counter. Display Driver information system. Date and time display. Mileage recorder. SpeedometerFuel gauge. Note The needles in the instrument cluster will sweep across the dials when you switch on the ignition. The instrument lighting illumination of dials and needles is switched on when the ignition is on and the vehicle's lights are off.
The instrument lighting is dimmed automatically as the daylight starts to fade. This function is intended to remind the driver to switch on the dipped-beam headlights in good time when light conditions become poor. Coolant temperature gaugeThe coolant temperature gauge fig. In order to avoid possible damage to the engine, please read the following notes for the different tempera-ture ranges.
Engine coldIf the needle is still in the lower range of the dial, this indicates that the engine has not yet reached operating temperature. Avoid high engine speeds, full acceleration and heavy engine loads. Normal temperatureIn normal operation the needle will settle somewhere in the centre of the dial once the engine has reached operating temperature. The needle may also go further up when the engine is working hard at high outside temperatures.
This is no cause for concern provided the warning symbol in the display does not start flashing. If the needle is at the top end of the dial, this means the coolant temperature is too high. Stop the vehicle, switch off the engine and wait for it to cool down. If the warning lamp starts flashing again after just a short distance, contact a qualified workshop. WARNING Before opening the bonnet and checking the coolant level, please observe the warning information on page , Working on components in the engine compartment.
Never open the bonnet if you can see or hear steam or coolant escaping from the engine compartment; there is a risk of being scalded. Wait until you can no longer see or hear escaping steam or coolant. Caution Additional lights and other accessories in front of the air inlet reduce the cooling effect of the radiator.
At high outside tempera-tures and high engine loads, there is a risk of the engine over-heating. The front spoiler also ensures proper distribution of the cooling air when the vehicle is moving. If the spoiler is damaged this can reduce the cooling effect, which could cause the engine to overheat.
You should obtain professional assistance. Rev counterThe rev counter indicates the number of engine revolu-tions per minute. You should select a lower gear if the engine speed drops below rpm. The start of the red zone on the dial indicates the maximum engine speed which may be used briefly when the engine is warm and after it has been run in properly. However, it is advisable to change up a gear or move the selector lever to D or lift your foot off the accelerator before the needle reaches the red zone.
CautionNever allow the rev counter needle page 11, fig. The start of the red zone on the dial is different for some engine versions. For the sake of the environmentChanging up a gear early will help you to save fuel and minimise engine noise. Starting check procedure auto-check control The auto-check control checks important components and vehicle systems. These background checks are run constantly, as long as the ignition is switched on page You can start the check procedure manually by pressing the button with the ignition switched on.
Calling up driver messages againA red or yellow symbol appearing in the instrument cluster display is normally accompanied by a corresponding message.
The message will disappear from the display after about 5 seconds. If required, you can call up the message again by briefly pressing the button. Setting speed warningYou can press the button briefly to set speed limit warning 1 while the vehicle is moving page If you press and hold the button, this will cancel the speed warning. It is then not possible to change the minutes or the date manually. Note The digital clock and mileage recorder displays are switched on for about 30 seconds when the driver's door is opened.
When the ignition is switched off, the clock and date display can be switched on for about 30 seconds by pressing the button page 12, fig. The mileage is stated in kilometres km or miles. The trip recorder shows the distance that has been travelled since it was last reset. It is used to measure individual journeys. The last digit of the trip recorder indicates distances of metres or tenths of a mile. The trip recorder can be reset to zero by pressing the reset button fig.
Fault displayIf there is a fault in the instruments, the letters dEF appear perma-nently in the trip recorder display. Please have the fault rectified as soon as possible. ImmobiliserWhen the ignition is switched on, the security programming of the ignition key is verified electronically. If an uncoded key is used, SAFE will appear continuously in the mileage recorder display.
The vehicle cannot then be driven page Note The date, time and recorded mileage will continue to be displayed for about 30 seconds after you switch off the ignition. The digital clock and mileage recorder displays are switched on for about 30 seconds when the driver's door is opened.
When the ignition is switched off, the mileage recorder can be switched on for about 30 seconds by pressing the button page 12, fig.
❿
Comments
Post a Comment